Heaters & Pre-Heaters

1.2mbtu Heatec Hot Oil Heater

1.2MBTU Hot Oil Heater

More Photos:

1.2MBTU Heatec Hot Oil Heater

1.2 MBTU Heatec Hot Oil Heater, Combo burner, has gas train and fuel pump, was running on gas, worked fine at shut down a few weeks ago

More Photos:

1.5MBTU Stansteel Heater

1.5mbtu Heater . Stansteel . Model: H.O.H. Exchanger Finned . Serial: 138-1066-00.Cstill in use. Coming offline soon.

More Photos:

1MBTU Heatec Heater

1992 - 1 MBTU set up on natural gas. It was reported to me that the coils were replaced 4 seasons ago. The controls have also been updated with new fire eye and a Floorcat Temp warning system. Model #: HCS-100-G . Serial #; H91-189. Just taken out of service, worked fine at that time but pump has small leak.

More Photos:

2MBTU Hot Oil Heater

GEN TEC HOT OIL HEATER. 2001- 2,000,000 TWO MILLION GEN TEC HOT OIL HEATER......PARTS LOW CONTROL W/ 10 HP MOTOR.....POWER FLAME BURNER S/N 039361690.....ALL STARTERS AND BREAKER WITH WIRING. NOW DISCONNECTED.

More Photos:

1.5MBTU Sundance Heater

Sundance . Honeywell Burner . Skid Mounted . 1.5mbtu.

More Photos:

CMI PRE-HEATER

we believe CMI Came off CMI 400tph drum plant, ran fine at shut down last year Has lifting eyes Partlow temp control Located in our yard in Murfreesboro TN

More Photos:

1MBTU Childers Heater

Childers Heater . Webster burner . 1mbtu . 3hp pump.

More Photos:

Gencor Hot Oil Heater

Refurbished Sellers 130 Natural Gas Hot Oil Heater • New Beckett Natural Gas Burner 2M BTU Input • New wiring and disconnect • New burner cover • New Peeco flow valve • New stack high limit • Tested fired at factory on test stand

More Photos:

Gencor Pre-Heater

Gencor Pre-Heater

More Photos:

GENCOR ELECTRIC PRE_HEATER

Gencor (Hy-Way) MODEL# SA 150-8T-15, SN# 235 Inline (Electrically Heated) Fuel Pre-Heater Condition Good Mechanically (Has Skin Issues)

More Photos:

GENCOR IN-LINE PRE HEATER

Gencor (Hy-Way) MODEL # 0072-4ft-21 OIL-OIL, SN# 00272-4-21-125084 Inline (Oil Heated) Fuel Pre-Heater Very Good Condition

More Photos:

GENCOR PRE-HEATER

Gencor (Hy-Way) MODEL # 00164-4FT-15 OIL-OIL, SN# 00184-4-15-120508L Inline (Oil Heated) Fuel Pre-Heater Very Good Condition

More Photos:

GENCOR IN-LINE PRE HEATER

Gencor (Hy-Way) HY-WAY Model # 00184-4FT-15, SN# 00184-4-15-86626. Inline (Oil Heated) Fuel Pre-Heater Very Good Condition

More Photos:

GENCOR PARTS HEATER

Hot Oil Heater... 1.5 Mtu... Oil/ Gas (Has Gas Train)... Missing Some Parts........

More Photos:

HFP-100R fuel preheater

HFP-100R fuel preheater is a free-standing unit. It is designed to preheat heavy fuel as it flows from a fuel storage tank to the burner of an aggregate dryer at a HMA plant. Preheating lowers the viscosity of the fuel so it can be properly atomized by the burner. The preheater heats the fuel to its optimum temperature for atomization. The preheater is controlled precisely to maintain that temperature within one or two degrees. The unit can raise the fuel temperature 100 degrees above its storage temperature at a flow rate of 1,000 gallons per hour. The fuel is heated as it flows around the outside of finned coils in the unit. The finned coils are heated by thermal fluid that flows inside the finned coils. The thermal fluid must be provided by an external source such as a thermal fluid heater (not included). For optimal performance, the heater should be installed in an independent hot oil circuit with its own hot oil pump. COMPONENTS The main components of the fuel preheater are: - Shell - Insulation - Skin - Heating coils - Controls - Control panels - Piping and valves SHELL The shell of the fuel preheater is made from schedule 40 steel pipe, 12-inches in diameter. One end has a welded pipe cap. The other end is flanged and has a removable head that is bolted in place. The shell has two saddles that support the heater. The saddles are flanged at the bottom and predrilled for mounting bolts. Two lifting lugs are incorporated to facilitate lifting either the entire unit or the removable head with coils attached. One lug is welded to the shell. The other is welded to the removable head. INSULATION The shell is covered with 1-1/2 inches of pipe insulation. One end of the shell is also insulated. SKIN The shell is covered with 0.032-inch aluminum skin to protect the insulation. The skin has a baked-on ivory finish that is durable, long-lasting and virtually maintenance-free. HEATING COILS The heating coils are made from 1-1/4 inch diameter, schedule 40 pipe. The coils have serrated fins, which increase the heating surface of the pipe about 800 percent more than bare pipe. The serrations of the fins increase efficiency of heat transfer by increasing

More Photos:

Fuel Pre-Heater

Process Heating Per-Heater Parts Only Heater Body Good Missing Some Controls and Stand

More Photos:

Fuel Pre-Heater

Fuel Pre Heater Process Heating Electric 80 KW SN# 3769 With Fuel Pump

More Photos:

Fuel Pre-Heater

Fuel Pre-Heater Process Heating Fuel Pre-Heater Electric SN-2618

More Photos:

Fuel Pre-Heater

Process Heating Pre-Heater Electric 90KW

More Photos:

HAVE OIL IN TANK AND NO HEAT SOURCE, WE CAN HELP. RENT OUR ELECTRIC HEATER ELEMENT.

WE HAVE THIS HEATER ELEMENT FOR RENT. IF YOU HAVE A TANK WITH AC LEFT INSIDE AND NO HEATER TO HEAT UP. THIS UNIT WILL WORK FOR YOU. YOU PLACE UNIT ON TOP OF HARD AC AND IT SLOWLY MELTS AND LIQUEFIES....FYI-The wiring is 3-phase 480 volts Each wire has 37 ohms of resistance The three wires should attach to a 20 amp circuit (30 amp max) All wires are hot. There is no on/off switch on the heater, Therefore once electricity is connected and turned on, the heater will begin to warm unit is 13" round and 7' long...... CALL TODAY FOR DETAILS

More Photos:

1.5MBTU BURKE HEATER

This Burke ran on natural gas It was replaced when it could not heat 60,000 Gallons of AC and heat the Batch Plant. Burke 150 1.5 MBTU Ran on Natural Gas High efficiency "Long Body" design 4' X 5' X 22'

More Photos:

American Hydrotherm

One (1) Used TCU temperature control unit

More Photos: