WEM4000 Pro Controls
Just taken offline
Serial No. 11723801
120 Volt
60Hz
NOTE- Controls were purchased new 6 years ago and have Windows 7 software, they will need to be updated to Windows 10, would cost approx. $10,000 from WEM.
Currently running a batch plant that's being replaced with another plant this winter .
More Photos:
BC250 Controls
BC250 Controls
More Photos:
NEMA Motor Control Center
Motor Control Center
Large Nema Cabinet
1200 Amp Main Plus a 300 Amp Main
Ran a 350 TPH Drum Plant
Starters For: Drum, Baghouse, Slat, Conveyors, Compressors, Augers, Screen decks, Heater, Burner, Pugmill ETC
More Photos:
Refurbished Control House
Repaired and Ready To Go!
Can be painted any color desired
Inside can be finished as desired
This is a brand new control house. It is currently only primed, and can be painted any color the customer prefers. No MCC, just 120v plugs and led overhead lighting. No counter tops included but could be added. The interior walls are finished with white paneling, the floor will be gray VCT tile (like cedar rapids used to use), or we could do raised rubber roundel (like astec) for an additional charge.
The ceiling is dropped tile acoustical with led strip lighting. Plugs were placed in the ceiling so that red night lighting could be easily added. If the potential buyer wants an MCC in the lower level, it is possible, manufacturer just need a motor list and will need to remove some of the 3/4 floor and add some metal (not a big deal or required, just a suggestion).
More Photos:
Gen III Burner Controls
Serial No. 3544N
Mode: Gen III
DWG No. Dy6320 B
Volts 110
Frequency 60HZ
Date or Manufacture: 10-26-83
More Photos:
Gen III Burner Controls
Model: Gen IIl
Serial: 4230N
DWG #: DY6320 C
Volts 110
Frequency: 60hz
Date of Manufacture: 11/13/86
More Photos:
Stationary (25'x14'x12') 280 Degree CMI Control House
Make: CMI
Size: 25' x 14' x 12'
Portability: Stationary
280 Degree
2 room
No motors or starters
25'L x 14' with added roof(12' if removed),12' tall
Carrier AC unit
Seltec batch plant controls
Load out controls
Gen11 Burner controls
Still erected
More Photos:
BC3300 Burner Controls
Hauck Burner Controls
BC3000 Burner Controls
More Photos:
CMI Control House and MMC Center
Brand: CMI
Control House
MCC Center
Impulse 11 Controls, updated and can be wired to latest Impulse controls
just came off of 300tph PF CMI Drum Plant,
Site upgraded/upsized components and a new control house and MCC center,
ran plant fine at shut down a few months ago
More Photos:
Astec (10'x12') Control House
The Astec 10’ x 12’ control house is mounted on the same portable framework as the self-erecting 70-ton capacity hopper, no controls included.
BUYER IS RESPONSIBLE FOR REMOVING CONTROL HOUSE FROM SEB.
More Photos:
Controls
Controls
Model: Quantum Ver. 2000 Pro 3.20B Rev, A
A detailed list of equipment included in the package is in pictures.
More Photos:
Gencor Batch Plant Controls - Model: SL-300
Make: Gencor
Model: SL-300
Gencor Computer Batching Controls
Model SL-300 (In Cabinet) Gencor Manual Batching controls
Model SP-100 (In Cabinet) Full Manual Controls To operate "UP TO"
5 Agg Bins Hot Bins
Mineral Filler
Recycle
2 A.C.
4 Cold Feed
Up to 3 Asphalt Storage Silo's
Up To 2 Transfer Slats
One Main Slat
Tower Flop Chute
AMP Meters
Gencor Gen III Burner Controls
Monitors and printers
M.C. Starters to run Motors
No baghouse starter/brakers included
ANY AND ALL MANUALS
All equipment disconnected and stored
More Photos:
Gen III Burner Controls
Gencor
GEN III BURNER CONTROLS
Table Top Controls
Auto Damping Controls
SO Cable Wires
More Photos:
Portable (8' X 30") 280 Degree Control House
8' x 40'
3 Room
280 degree front room
Portable
Came off 400tph plant
Lufkin Trailer
Controls EZ Blend Computer Controls
Gen 111 Gencor Burner Controls
Full Start Stop Station
2- Silo Load Out Controls
2- Rap Bin Controls (D.C.)
5 Cold Feed Controls (D.C.)
Central Air And Heat and Window Unit for Really Hot Days
Middle Room
M.C Center Cabinet Style
M.C. Panels
Square D Starters
Rear Room Parts Room with Shelves
Quick Disconnects
More Photos:
Portable (8'x25') Control Van
Portable Control Van
8'x 25'
Tandem Axle (10 Lug 10-22.00 Tires)
Drum Plant Controls
Aesco Madsen Control Center
Lebra Computer Controls
Hauck Burner Controls
Baghouse Controls
D. C. Cold Feed Controls
MC. Center
Twin 400 amp Mains
All starters and Breakers in NEMA Cabinet
Air/Heat
More Photos:
Portable (10.5'x20') CMI UDM 1200 Control House
Make: CMI
Size: 10.5' x 20'
Portability: Portable
CMI 10.5’x 20’, single axle carrier, side door, steps, glass on 3 sides, MCC in rear of control room, heated/air conditioned.
Starters for 150HP fan and 75Hp drum motors available but not in unit at present time. This control house was on a CMI UDM 1200 plant.
The front- The plant computer is an Industrial pc-610 running Martin Engineering blending software. No load-out automation.
Manual motor start/stop Button Station, Burner controller, lime controls and oil injection controls and feed bin controls (no DC cards).
Many OEM Operators Manuals included.
The rear on CH- The 480V, 3 phase, 60Hz.motor control center has a total of 17 starters (4 additional - #4 Allen-Bradley’s available) and 20 Breakers.
6- size 0; 3- size 1; 5- size 2; 2- size 3; 1-size 4
120V Transformer with distribution panel breakers.
Do not know if the 2 DC Feed bin controllers in the electrical room work.
More Photos:
Stationary (8'x20') 280 Degree Control House w/mcc Center
Make:
Size: 8' x 20'
Portability: Stationary
280 Degree View
Air and Heat Unit
Aesco Madsen Control System
(Burner Controls, 3 Cold feed Bin Controls, 1 Rap Bin, 2 Silo Load Out,
A.C. Controls)
M.C. Center
(This plant was set up to 400 TPH CMI plant with 400 tph Slat, 70,000
ACFM Baghouse, 3 Cold Feed, 1 Rap Feeder, 2 A.C. Tanks)
More Photos:
Batch Plant Controls - Model: WEM HMB 3000
Make: WEB
Model: HMB 3000 batch plant controls
Controls worked fine at plant shut down a few years ago.
Controls were on a 6,000lb h&b batch plant.